Re: Judson TNT Refurbish

by Mo Sat Mar 08, 2014 7:31 am

I see. That little opening was full of gunk.

by milspec6 Sat Mar 08, 2014 9:58 am

Mo wrote:I see. That little opening was full of gunk.

Previous owner must have over-filled the tank a few times then. The water bath should keep the "gunk" from becoming airborne in that upright set-up, but if the waste tank gets too full, it will just get sucked right into the blower.

I think that is why Judson moved the blower location a little on the latest model.

by Mo Sat Mar 08, 2014 11:25 am

I think now they come with a blower manifold

by Mo Sat Mar 08, 2014 11:47 am

I'm so sick on sanding a few more areas to go

Judson TNT Refurbish - Page 3 Before10

Looked better after I pressure washed it
Judson TNT Refurbish - Page 3 Before11

Getting the paint off the top and underneath the mounting brackets are a pain.
Judson TNT Refurbish - Page 3 After_10

I have to remove that blower to tank pipe. It wouldn't budge gonna have to heat that baby up. Any idea were I can get another one preferably stainless. Do you guys think I could use flexible exhaust hose? Or will it collapse.
Judson TNT Refurbish - Page 3 Before12

The panel and gauges had paint on it

Judson TNT Refurbish - Page 3 Before13

by Larry Henson Sat Mar 08, 2014 4:50 pm

That thing sure does look GOOD in it's stainless form. Polish and buff it and you would have to wear sunglasses around it. The shimmer alone would attract customers.

by Larry Henson Sat Mar 08, 2014 4:57 pm

Mo, you have to admit that in it's present state it looks awesome!!!! Polished metal and braided lines would stand out from other cleaners. Guess I'm a sucker for polished metal instead of paint. Either way I can't wait to see your finished product.

by milspec6 Sat Mar 08, 2014 5:01 pm

I am with Larry, it looks sharp like that!

by Pro Touch Sat Mar 08, 2014 5:04 pm

Mo, can I send you mine? Laughing

That looks awesome.

by milspec6 Sat Mar 08, 2014 5:06 pm

Mo, might be the best stripper in Arizona...so to speak. wink

by Larry Henson Sat Mar 08, 2014 5:07 pm

Yeah and you don't have to worry about scratching the paint. Stainless is TOUGH and that is why people pay for that type of machine. Don't try and put lipstick on a PIG (JMO). I've said enough and it's your machine.....I'm sure the end product will look good either way you go.

by Larry Henson Sat Mar 08, 2014 5:09 pm

milspec6 wrote:Mo, might be the best stripper in Arizona...so to speak.

I second that. Laughing

by ACE Services Sat Mar 08, 2014 5:59 pm

Yes I would use the rubber marine exhaust hose to replace the old elbow. Because I have tried to get a replacement made at a muffler shop and they can't make the bend as tight. I like the other because when you get it cut and fitted then your done it won't rust out like the metal ones.

by ACE Services Sat Mar 08, 2014 6:06 pm

Yes I would use the rubber marine exhaust hose to replace the old elbow. Because I have tried to get a replacement made at a muffler shop and they can't make the bend as tight. I like the other because when you get it cut and fitted then your done it won't rust out like the metal ones.

by Mo Sat Mar 08, 2014 6:06 pm

ACE Services wrote:Yes I would use the rubber marine exhaust hose to replace the old elbow. Because I have tried to get a replacement made at a muffler shop and they can't make the bend as tight. I like the other because when you get it cut and fitted then your done it won't rust out like the metal ones.

I think Napa sells marine hose. Were did you get yours ACE?

by ACE Services Sat Mar 08, 2014 7:27 pm

Service dept at a boat dealer sells

by ACE Services Sat Mar 08, 2014 7:40 pm

Mo
That wire on the left rear of the unit did you take it loose or was it like that when you got it.
The reason I ask is that's your waste tank shutdown switch. If it was disconnected when you got it that's why the hole was full of gunk. If you disconnected it then test it. It should be a normally open and close when you lift the switch inside the tank if no moving parts inside again there's the problem.

by Mo Sat Mar 08, 2014 8:02 pm

It was disconnected when I got it. Ill test it out when I get it back together

by Mo Sat Mar 08, 2014 8:05 pm

ACE Services wrote:Service dept at a boat dealer sells

I check with Naapa all they had was the straight length. We do have a boat dealers a couple of cities away

by Mo Sat Mar 08, 2014 8:23 pm

Larry Henson wrote:Mo, you have to admit that in it's present state it looks awesome!!!! Polished metal and braided lines would stand out from other cleaners. Guess I'm a sucker for polished metal instead of paint. Either way I can't wait to see your finished product.

The more I see it shine the more I like. It will be cheaper too. The only thing I don't like is the weld burn marks

by milspec6 Sat Mar 08, 2014 8:41 pm

If it is trouble finding that marine hose, just get me the dimensions and I'll send you the part. My brother owns a boat shop, shouldn't be a problem.

by Davey Cracker Sat Mar 08, 2014 9:44 pm

Mo wrote:
ACE Services wrote:Service dept at a boat dealer sells

I check with Naapa all they had was the straight length. We do have a boat dealers a couple of cities away

Mo, you can order the $hit and day long on the InterWebs, or just have Rob get it for you! cheers

by Mo Mon Mar 10, 2014 7:49 pm

I messed around with the engine today. I put new plugs, oil filter, oil. I wouldn't stay running without carb fluid, the fuel pump is pumping fuel. The carb is probably full of gunk, I think it was sitting for a while. I took to the small engine shop to have them service and tune it up. Be ready when I get back from Californnication.

by Davey Cracker Mon Mar 10, 2014 8:06 pm

Mo wrote:I messed around with the engine today. I put new plugs, oil filter, oil. I wouldn't stay running without carb fluid, the fuel pump is pumping fuel. The carb is probably full of gunk, I think it was sitting for a while. I took to the small engine shop to have them service and tune it up. Be ready when I get back from Californnication.

You should have brought it to CA, I'd have done it free. wink

by Davey Cracker Mon Mar 10, 2014 8:07 pm

OH and don't forget to bring the RC99, Mo. cheers

by Mo Mon Mar 10, 2014 8:31 pm

Hopefully I can fit everything in my little corolla

by Sponsored content